IEC 61347-1:2015 灯具控制装置 - 第1部分:通用和安全要求

标准编号：IEC 61347-1:2015

中文名称：灯具控制装置 - 第1部分:通用和安全要求

英文名称：Lamp controlgear - Part 1: General and safety requirements

发布日期：2015-02-19

标准范围

新的！IEC 61347-1:20 15作为IEC标准+61347-1:20 15提供，其中包含国际标准及其红线版本，显示了与上一版本相比技术内容的所有变化。IEC 61347-1:20 15规定了直流使用的灯具控制装置的一般和安全要求。高达250 V和/或交流电的电源。在50 Hz或60 Hz下提供高达1 000 V的电源。本第三版取消并取代了2007年出版的第二版、修正案1:20 10和修正案2:20 12。本版构成技术修订版。与上一版相比，此版本包括以下重大技术变更:a)附加标记要求；b)爬电距离和间隙的附加要求:-用于工作频率高达30kHz的工作电压；-用于工作频率高于30kHz的工作电压；-用于脉冲和谐振电压点火；-用于基本、补充和加强绝缘；-用于电路之间的绝缘；-用于涂覆或灌封的控制装置；c)修改ELV和FELV的定义；d)修改示意图，显示不同的控制装置分类和绝缘要求；e)范围扩展；f)新附件A:确定导电部件是否为可能引起电击的带电部件的试验；g)新的附件M:控制装置的爬电距离和间隙，其中可能需要更高程度的可用性（抗冲击III类）；h)新附录Q:Up计算示例；i)新附件P:通过使用涂层或灌封防止污染的灯具控制装置的爬电距离、间隙和隔离距离(DTI)；j)新附件R:爬电距离和间隙的概念。

NEW! IEC 61347-1:2015 is available as IEC Standards+ 61347-1:2015 which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 61347-1:2015 specifies general and safety requirements for lamp controlgear for use on d.c. supplies up to 250 V and/or a.c. supplies up to 1 000 V at 50 Hz or 60 Hz. This third edition cancels and replaces the second edition published in 2007, Amendment 1:2010 and Amendment 2:2012. This edition constitutes a technical revision.This edition includes the following significant technical changes with respect to the previous edition:
a) additional marking requirements;
b) additional requirements for creepage distances and clearances:
- for working voltages with operating frequencies up to 30 kHz;
- for working voltages with higher operating frequencies than 30 kHz;
- for impulse and resonance voltages ignition;
- for basic, supplementary and reinforced insulation;
- for insulation between circuits;
- for coated or potted controlgear;
c) modification of definition of ELV and FELV;
d) modification of schematic drawing, showing the different controlgear classification and insulation requirements;
e) scope extension;
f) new Annex A: test to establish whether a conductive part is a live part which may cause an electric shock;
g) new Annex M: creepage distances and clearances for controlgear where a higher degree of availability (impulse withstand category III) may be requested;
h) new Annex Q: example for Up calculation;
i) new Annex P: creepage distances and clearances and distance through isolation (DTI) for lamp controlgear which are protected against pollution by the use of coating or potting;
j) new Annex R: concept of creepage distances and clearances.

标准预览图