IEC 60512-1:2018 电气和电子设备用连接器试验和测量第1部分:总规范

标准编号：IEC 60512-1:2018

中文名称：电气和电子设备用连接器试验和测量第1部分:总规范

英文名称：Connectors for electrical and electronic equipment - Tests and measurements - Part 1: Generic specification

发布日期：2018-10-22

标准范围

IEC 60512-1:20 18作为IEC 60512-1:20 18 RLV提供，其中包含国际标准及其红线版本，显示了与上一版本相比技术内容的所有变化。IEC 60512-1:20 18旨在用作电连接器测试和测量规范的基础。它为IEC 60512系列内的测试和测量提供了指导和参考。除了适用于IEC 60512系列任何部分的基本术语和定义之外，它还包括测试和测量各个阶段（准备、测试和测量、要求、文档）的描述和实践。本标准应与IEC 60512-1-101和IEC 60512系列的相关部分结合使用。第60512-1-100部分提供了IEC 60512系列中公布的现有测试和测量方法的列表。详细测试和测量规范适用于技术委员会48范围内的电连接器及其组件（如连接器插件、连接器外壳、锁定机构、触点和终端）。如果在详细产品说明书中有规定，它们也可用于类似器械。详细测试和测量规范与详细产品规范一起使用，详细产品规范规定了要使用的测试、每个测试所需的严重程度以及允许的性能限制。详细产品规范还规定了对所考虑的连接器或其部件类型进行测试时可能需要的程序偏差，并进一步规定了可能需要的任何特殊程序。第五版取消并取代了2001年出版的第四版。它构成技术修订。与上一版相比，此版本包括以下主要技术变更:-在条款3中，仅定义了与测试相关的术语，连接器术语参考IEC 61076-1。-增加第4条（试验和测量规范的编号）。-增加子条款5.1.2（校准）。-在条款6（测试）中，测试程序遵循IEC 60068-1。关键词:连接器，测试规范

IEC 60512-1:2018 is available as IEC 60512-1:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 60512-1:2018 is intended to be used as a basis for tests and measurements specifications for electrical connectors. It provides guidance and reference for tests and measurements within the IEC 60512 series. It includes the description and the practice of the various phases of tests and measurements (preparation, tests and measurements, requirements, documentation), in addition to basic terms and definitions applicable to any part of the IEC 60512 series. This standard shall be used in conjunction with IEC 60512-1-101 and relevant part(s) of series IEC 60512. Part 60512-1-100 provides the list of the existing test and measuring methods published within series IEC 60512. Detail tests and measurements specifications are applicable to electrical connectors and their components (e.g. connector inserts, connector housings, locking mechanisms, contacts and terminations) within the scope of technical committee 48. They may also be used for similar devices when specified in a detail product specification. Detail tests and measurements specifications are used in conjunction with detail product specifications which prescribe the tests to be used, the required degree of severity for each of them and the permissible performance limits. The detail product specification also specifies the deviations in procedures, which may be required when applying a test to the type of connector or its component under consideration, and it further specifies any special procedures which may be required. This fifth edition cancels and replaces the fourth edition, published in 2001. It constitutes a technical revision. This edition includes the following main technical changes with respect to the previous edition:
– in Clause 3, only terms relating to the testing are defined, and IEC 61076-1 is referred to for terms of connectors.
– Clause 4 (Numbering of tests and measurement specification) is added.
– Subclause 5.1.2 (Calibration) is added.
– in Clause 6 (Test), test procedure follows IEC 60068-1.

Key words: Connectors, Test Specification

标准预览图