IEC 60603-7:2020 电子设备连接器 - 第7部分:8路 非屏蔽 空闲和固定连接器的详细规范

标准编号：IEC 60603-7:2020

中文名称：电子设备连接器 - 第7部分:8路 非屏蔽 空闲和固定连接器的详细规范

英文名称：Connectors for electronic equipment - Part 7: Detail specification for 8-way, unshielded, free and fixed connectors

发布日期：2020-10-09

标准范围

IEC 60603-7:20 20作为IEC 60603-7:20 20 RLV提供，其中包含国际标准及其红线版本，显示了与上一版本相比技术内容的所有变化。IEC 60603-7:20 20涵盖8路、非屏蔽、自由和固定连接器，旨在规定IEC 60603-7-x连接器系列的通用尺寸（接口尺寸）、机械、电气和环境特性以及测试。这些连接器可互配（根据IEC 61076-1 2级），并可与其他IEC 60603-7系列连接器互操作。第四版取消并取代了2008年出版的第三版及其修正案1:20 11和修正案2:20 19。它构成技术修订。与上一版相比，此版本包含以下重大技术变更:-修订了互配性和互操作性的定义；增加了新的定义。-图5中尺寸AZ2的校正尺寸线。-图A.1中尺寸F1的修正尺寸线。-将ISO/IEC 11801的参考修订为ISO/IEC 11801-1。-增加了下限温度和上限温度定义。-将表1修订为表8，因此列顺序为最小-标称-最大尺寸（升序）。-修正表7:气候类别和90°C的上限温度值（与图10中的图表和图10中的注释1一致）。-修订了8.2接触电阻中的措辞，以求澄清。-修订了图11和图12以及以下关键字中的措辞，以便澄清。-删除导言图下的句子。-增加了附件E。

IEC 60603-7:2020 is available as IEC 60603-7:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 60603-7:2020 covers 8-way, unshielded, free and fixed connectors and is intended to specify the common dimensions (interface dimensions), mechanical, electrical and environmental characteristics and tests for the family of IEC 60603-7-x connectors. These connectors are intermateable (according to IEC 61076-1 level 2) and interoperable with other IEC 60603-7 series connectors. This fourth edition cancels and replaces the third edition, published in 2008, its Amendment 1:2011 and its Amendment 2:2019. It constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition:
- Revised the definitions for intermateability and interoperability; added new definitions.
- Corrected dimension line for dimension AZ2 in Figure 5.
- Corrected dimension line for dimension F1 in Figure A.1.
- Revised the reference to ISO/IEC 11801 to ISO/IEC 11801-1.
- Added lower limiting temperature and upper limiting temperature definitions.
- Revised Table 1 to Table 8 so the column order is Minimum-Nominal-Maximum dimensions (ascending order).
- Corrected Table 7: Climatic category and Upper temperature values to 90 °C (to be consistent with the graph in Figure 10 and Note 1 in Figure 10).
- Revised the wording in 8.2, contact resistance, for clarification.
- Revised Figure 11 and Figure 12 and the wording in the Key below for clarification.
- Removed the sentences under the figure in the Introduction.
- Added Annex E.

标准预览图