ISO 19085-9:2019 木工机械 安全 第9部分：带和不带滑台的圆锯工作台（带或不带滑台）
标准编号：ISO 19085-9:2019
中文名称：木工机械 安全 第9部分：带和不带滑台的圆锯工作台（带或不带滑台）
英文名称：Woodworking machines — Safety — Part 9: Circular saw benches (with and without sliding table)
发布日期：2019-04
标准范围
本文件给出了固定式和可移动式圆锯台（带或不带滑动工作台和/或可拆卸动力进给装置）的安全要求和措施，也称为“台式锯”（在美国），以下简称“机器”，旨在切割具有与木材相似物理特性的木材和材料。注1:关于固定式和可移动式机器的定义，见ISO 19085-1:2017，3.4和3.5。当这些机器按照预期和制造商预见的条件（包括合理可预见的误用）进行操作、调整和维护时，它涉及第4条中列出的与这些机器相关的所有重大危险、危险情况和事件。此外，还考虑了运输、组装、拆卸、禁用和报废阶段。注2:有关相关但不显著的危险，例如机架的锐边，请参见ISO 12100:2010。它也适用于装有以下一个或多个装置或工作装置的机器，其危险已得到处理:-主锯片和划线锯片通过工作台升降的装置；-倾斜主锯片和划线锯片进行斜切的装置；-记分装置；-一次使用宽度不超过20 mm的铣刀开槽的装置；-可拆卸的供电装置；-附加手动滑动台；-电动工件夹紧装置。注3:圆锯台用于剥离、横切、尺寸标注和开槽。本文件不适用于:a） 用于建筑工地户外使用的可移动/可置换机器；注4建筑工地锯（承包商锯）包含在ISO 19085-10:2018的要求中。b） 手持式木工机械，包括允许其在不同模式下使用的任何改装，即台式安装；c） 拟在潜在爆炸性环境中使用的机器；d） 在其作为国际标准发布之日之前制造的机器；e） 最大锯片直径为≤315毫米。注5:IEC 62841-1:2014和IEC 62841-3-1:2014中涉及可移动电动工具。
This document gives the safety requirements and measures for stationary and displaceable circular saw benches (with or without sliding table and/or demountable power feed unit), also known as "table saws" (in the USA), hereinafter referred to as "machines", designed to cut wood and material with similar physical characteristics to wood.NOTE 1 For the definition of stationary and displaceable machine, see ISO 19085？1:2017, 3.4 and 3.5.It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to these machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account.NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.It is also applicable to machines fitted with one or more of the following devices, or working unit, whose hazards have been dealt with:— device for the main saw blade and scoring saw blade to be raised and lowered through the table;— device to tilt the main saw blade and scoring saw blade for angled cutting;— device for scoring;— device for grooving with milling tool with a width not exceeding 20 mm in one pass;— demountable power feed unit;— additional manually operated sliding table;— powered work-piece clamping device.NOTE 3 Circular saw benches are used for ripping, cross cutting, dimensioning and grooving.This document does not apply to:a) transportable/displaceable machines intended for outdoor use on building sites;NOTE 4 Building site saws (contractor saws) are covered by the requirements of ISO 19085？10:2018.b) hand held woodworking machines including any adaptation permitting their use in a different mode, i.e. bench mounting;c) machines intended for use in a potentially explosive atmosphere;d) machines manufactured before the date of its publication as an International Standard;e) transportable machines with a maximum saw blade diameter of ≤315 mm.NOTE 5 Transportable motor-operated electric tools are dealt with in IEC 62841？1:2014 and IEC 62841？3？1:2014.
标准预览图
