ISO 17607-1:2023 钢结构 钢结构工程的施工 第1部分：一般要求、术语和定义

标准编号：ISO 17607-1:2023

中文名称：钢结构 钢结构工程的施工 第1部分：一般要求、术语和定义

英文名称：Steel structures — Execution of structural steelwork — Part 1: General requirements and terms and definitions

发布日期：2023-12

标准范围

本文件定义了结构钢结构执行的一般要求:—？钢结构建筑；—？以类似建筑物的方式设计、制造和建造的一般结构，具有类似建筑物的抗载荷元件，例如设备、储罐、容器和管道的支撑框架；—？起重机支撑结构；—？典型的道路和人行桥，包括使用轧制截面、焊接板梁或桁架（格子）建造的桥梁。本文件适用于由以下材料生产的结构或装配式部件:—？标称屈服强度不超过700？MPa，厚度为3？mm及以上；—？标称屈服强度不超过700？MPa，包括标准范围和定制-通过焊接制造的轧制产品和空心型材。本文件也适用于钢和混凝土组合结构中的钢构件，以及钢与其他材料结合的结构中的钢构件。本文件定义了与钢结构的类型和形状无关的要求，包括承受疲劳或地震载荷的结构。需求以执行级别来表达。本文件没有定义其他类型装配式钢结构的所有要求（例如，铁路桥、使用焊接箱形截面或拱形箱的道路和人行天桥、跨度超过100？m的斜拉桥、移动桥梁、单轨铁路、钢塔、桅杆、烟囱、筒仓、储罐、管道、天线、海上平台）。然而，本文件提供了有关制造和安装实践的一般指南，可与此类结构的适当ISO、地区或国家设计标准一起使用。本文档不涵盖以下内容的要求:—？片材；—？不锈钢的制造。本文件不适用于钢结构设计。笔记？设计是设计-制造-安装序列不可分割的一部分，包括公差的应用，不能孤立地考虑。本文件旨在酌情与国家标准和其他文件一起使用，遵守本文件中有关此类使用的规定。

This document defines general requirements for the execution of structural steelwork for:

—     structural steel buildings;

—     general structures, designed, fabricated, and erected in a manner similar to buildings with building-like load-resisting elements, e.g. support framing for equipment, tanks, vessels, and pipelines;

—     crane-supporting structures;

—     typical roadway and pedestrian bridges including those constructed using rolled sections, welded plate girders, or trusses (lattices).

This document applies to structures or fabricated components that are produced from:

—     hot-rolled and cold-formed structural steel products up to and including a nominal yield strength of 700 MPa with a thickness of 3 mm and above;

—     hot-finished and cold-formed structural steel hollow sections, up to and including a nominal yield strength of 700 MPa, including standard range and custom-made rolled products and hollow sections manufactured by welding.

This document also applies to steel components in composite steel and concrete structures, and in structures combining steel with other materials.

This document defines requirements independent of the type and shape of the steel structure, including structures subjected to fatigue or seismic loading. The requirements are expressed in terms of execution levels.

This document does not define all requirements for other types of fabricated steel structures (e.g. railway bridges, roadway and pedestrian bridges using welded box sections or arch boxes, cable-supported bridges over 100 m span, moving bridges, monorails, steel towers, masts, chimneys, silos, tanks, pipelines, antennae, offshore platforms). However, this document provides general guidance regarding fabrication and erection practices that may be used together with the appropriate ISO, regional or national design standards for such structures.

This document does not cover requirements for the following:

—     sheeting;

—     fabrication of stainless steels.

This document does not apply to design of steel structures.

NOTE            Design is inextricably a part of the design-fabrication-erection sequence, including the application of tolerances, and cannot be considered in isolation.

This document is intended to be used, as appropriate, together with national standards and other documents, observing the provisions in this document concerning such use.

标准预览图