ISO 8132:2022 液压传动 16MPa（160巴）和25MPa（250巴）系列的单杆液压缸 辅助设备安装尺寸
标准编号：ISO 8132:2022
中文名称：液压传动 16MPa（160巴）和25MPa（250巴）系列的单杆液压缸 辅助设备安装尺寸
英文名称：Hydraulic fluid power — Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250 bar) series
发布日期：2022-04
标准范围
本文件规定了16？附件互换性所需的安装尺寸？MPa（160？bar）中型系列钢瓶符合ISO？6020？1和25？MPa（250？bar）系列气缸符合ISO？6022.附件专门设计用于按照ISO？6020？1和ISO？6022，但这并不限制它们的应用[1]。本文件涵盖以下附件，根据ISO？6099:—？AP2？-杆U形夹，内螺纹（见图？1和表？1）；—？AF3？-杆法兰，圆形（见图？2和表？2）；—？AB4？-直形U形支架（见图？3和表？3）；—？AB3？-有角度的U形夹支架（见图？4和表？4）；—？AT4？-耳轴支架（见图？5和表？5）；—？匿名问:-枢轴销，滑动轴承（卡环型）（见图？6和表？6）；—？AA4-S-枢轴销，滑动轴承（分离销型）（见图？7和表？7）；—？AA6-R-枢轴销，球面轴承（卡环型）（见图？6和表？6）；—？6-？-枢轴销，球面轴承（分离销型）（见图？7和表？7）；—？AP6？-杆眼球形，内螺纹（见图？8和表？8）；—？AP4？-杆眼普通，内螺纹（见图？9和表？9）。这些附件用于液压缸上，以机械方式传递缸力。这些附件的设计基于根据ISO规定的气缸内径和压力产生的最大力？3320和ISO？2944.本文件仅适用于按照本文件制造的产品的尺寸标准；它不适用于它们的功能特征。？[1]？1？酒吧？=？0,1？MPa？=？105？Pa;1？MPa？=？1？N/mm2。
This document specifies the mounting dimensions required for the interchangeability of accessories for 16 MPa (160 bar) medium series cylinders in accordance with ISO 6020？1 and for 25 MPa (250 bar) series cylinders in accordance with ISO 6022. The accessories have been designed specifically for use with cylinders manufactured in accordance with ISO 6020？1 and ISO 6022, but this does not limit their application[1].This document covers the following accessories, identified in accordance with ISO 6099:— AP2 — rod clevis, female thread (see Figure 1 and Table 1);— AF3 — rod flange, circular (see Figure 2 and Table 2);— AB4 — clevis bracket, straight (see Figure 3 and Table 3);— AB3 — clevis bracket, in angle (see Figure 4 and Table 4);— AT4 — trunnion bracket (see Figure 5 and Table 5);— AA4-R — pivot pin, plain bearing (snap ring type) (see Figure 6 and Table 6);— AA4-S — pivot pin, plain bearing (split pin type) (see Figure 7 and Table 7);— AA6-R — pivot pin, spherical bearing (snap ring type) (see Figure 6 and Table 6);— AA6-S — pivot pin, spherical bearing (split pin type) (see Figure 7 and Table 7);— AP6 — rod eye spherical, female thread (see Figure 8 and Table 8);— AP4 — rod eye plain, female thread (see Figure 9 and Table 9).These accessories are used on hydraulic cylinders for mechanically transmitting the cylinder force. The design of these accessories is based on the maximum forces resulting from the specified internal diameters of the cylinders and pressures according to ISO 3320 and ISO 2944.This document applies only to the dimensional criteria of products manufactured in conformity with this document; it does not apply to their functional characteristics. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.
标准预览图
