ISO 8133:2022 液压传动 单杆液压缸,16MPa（160 bar）小型系列 附件装配尺寸
标准编号：ISO 8133:2022
中文名称：液压传动 单杆液压缸,16MPa（160 bar）小型系列 附件装配尺寸
英文名称：Hydraulic fluid power — Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) compact series
发布日期：2022-05
标准范围
本文件规定了16？附件互换性所需的安装尺寸？MPa（160？bar）符合ISO？6020？2.附件已专门设计用于按照ISO制造的气瓶？6020？2，但这并不限制它们的应用[1]。本文件涵盖以下附件，根据ISO？6099:—？AP6-杆眼球形，内螺纹（见图？1和表？1）；—？AB5-U形夹支架，球眼，成角度（见图？2和表？2）；—？AA6-L-枢轴销、球面轴承、锁紧板（见图？3和表？3）；—？用于枢轴销的AL6锁定板（见图？4和表？4）；—？AP2-杆U形夹，内螺纹（见图？5和表？5）；—？AP4-杆眼普通，内螺纹（见图？6和表？6）；—？AB2-眼托槽（见图？7和表？7）；—？AB4-直U形夹支架（见图？8和表？8）；—？AA4-S-枢轴销，普通（开口销）（见图？9和表？9）；—？AA4-R-枢轴销，普通（环）（见图？10和表？10）；—？AT4-耳轴支架（见图？11和表？11）。这些附件用于液压缸上，以机械方式传递缸力。这些附件的设计基于根据ISO规定的气缸内径和压力产生的最大力？3320和ISO？2944.本文件仅适用于按照本文件制造的产品的尺寸标准；它不适用于它们的功能特征。？[1]？1？酒吧？=？0,1？MPa？=？105？Pa;1？MPa？=？1？N/mm2
This document specifies the mounting dimensions required for interchangeability of accessories for 16 MPa (160 bar) compact cylinders conforming to ISO 6020？2. The accessories have been designed specifically for use with cylinders manufactured in accordance with ISO 6020？2, but this does not limit their application[1].This document covers the following accessories, identified in accordance with ISO 6099:— AP6 — rod eye spherical, female thread (see Figure 1 and Table 1);— AB5 — clevis bracket, spherical eye, in angle (see Figure 2 and Table 2);— AA6-L — pivot pin, spherical bearing, locking plate (see Figure 3 and Table 3);— AL6 — locking plate for pivot pin (see Figure 4 and Table 4);— AP2 — rod clevis, female thread (see Figure 5 and Table 5);— AP4 — rod eye plain, female thread (see Figure 6 and Table 6);— AB2 — eye bracket (see Figure 7 and Table 7);— AB4 — clevis bracket, straight (see Figure 8 and Table 8);— AA4-S — pivot pin, plain (split pins) (see Figure 9 and Table 9);— AA4-R — pivot pin, plain (rings) (see Figure 10 and Table 10);— AT4 — trunnion bracket (see Figure 11 and Table 11).These accessories are used on hydraulic cylinders for mechanically transmitting the cylinder force. The design of these accessories is based on the maximum forces resulting from the specified internal diameters of the cylinders and pressures according to ISO 3320 and ISO 2944.This document only applies to the dimensional criteria of products manufactured in conformity with this document; it does not apply to their functional characteristics. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2
标准预览图
